Dell XPS M1330 / M1530

Dell XPS M1330 and the larger M1530 are laptops sold from 2007 to 2009. They work quite well out of the box with Arch and GNU/Linux in general.

Note: This article on pre-2010 hardware was almost completely rewritten in January 2021.

CPU

The CPU is either Intel Merom or Penryn. Despite their age, they are both x86_64 and thus supported by Arch. Remember to install intel-ucode for full stability.

BIOS

The last BIOS revision for this product was A15. You can see which version is in use on the startup screen. The best way to update to the last version is through Windows Update (on a still-supported version of Windows).

Alternatively, the BIOS can be updated in Arch using FreeDOS. Download the Dell image (M1330A15.EXE or M1530_A12.EXE) and follow the instructions given here.

Network

Ethernet

The ethernet interface is made by Broadcom. The tg3 kernel module should load automatically. To use it, install and enable your preferred network manager (see Network configuration).

Wireless

Make sure the wireless interfaces are unblocked.

Wi-Fi and/or Bluetooth can be turned on/off with a hardware switch located on the right-hand side of the laptop. The functionality can be changed in the BIOS settings.

Warning: Some users have reported problems with the wireless devices after migrating from Windows, leaving either/both of them permanently unusable! To avoid this, turn the hardware switch to 'on' and set it to control both Wi-Fi and Bluetooth in BIOS. Then boot into Windows one last time. If the devices are not working in Windows either, a Dell patch (R159805.EXE) may be of help.

Wi-Fi

See Wireless network configuration for details.

M1330 and M1530 were shipped with many different Wi-Fi chipsets. Check which one you have with lspci -k.

Intel chipset: 3945abg or 4965agn

The correct kernel module should load automatically.

Broadcom chipset: bcm43xx

You may try installing the broadcom-wl driver first. The wl module should load on boot.

If this fails, your only option is to use the b43 driver and associated firmware. The ssb module loads automatically but the b43 module needs to be enabled manually. Performance will not be great.

Bluetooth

Some units include a Bluetooth card. The correct kernel module should load automatically. To use it, install the bluez package (if not already present) along with additional packages mentioned in relevant articles. Then enable .

Graphics

Most units were shipped with an Nvidia 8400M-GS card (G86M). It is no longer properly supported by the proprietary NVIDIA driver. You have two options:

Use kernel mode setting (works out of the box)

Install (small improvement)

Performance will not be great. Expect frequent freezes under moderate loads.

Sound

Sound works very well with PulseAudio. Simply install the necessary packages if not already present.

If you prefer pure ALSA, be sure to unmute all channels. To get the microphone working, you may have to change the digital input source.

Touchpad

The Synaptics-made touchpad works well with libinput which is included with most desktop environments.

Extra media keys

The media buttons are detected automatically by udev. The MediaDirect (house) button can be reassigned for any purpose.

Fingerprint reader

Some units include a fingerprint reader made by SGS Thomson Microelectronics. It should work with the generic fprint driver. If not try the manufacturer-supplied ThinkFinger driver.

SD Card Reader

The device is recognized by the kernel. The adapter module is .

The card will be available for mounting under the device

Webcam

See Webcam setup for details.

Most units are equipped with a webcam, If it is not working, run the built-in diagnostics (available by pushing 'F12' during the POST screen, then selecting 'Diagnostics').

Sensors / Hardware info

Install i8k packages: i8kutils^AUR.

This will provide many useful information (temperature, fan speed, BIOS...) and utilities (fan monitor, BIOS update...). For CPU temps, use lm_sensors.

Hard Drive

If the hard drive clicks regularly, it may be suffering from this problem.

gollark: Oh, and instead of writing `"tick-instances1.csv"` all over the place maybe make it a constant.

gollark: Looking at MainApplication.py:> objects = []This is not a very descriptively named thing. There should probably be a comment.> `def populate(self):`Arguably, it isn't very good design to make the code responsible for display *also* directly handle directly loading CSVs and such. Maybe this should be separated out more.> `def increment(self):`This does not appear to save anywhere, although I may have missed that bit.

gollark: Also also also, the ` ticks_count = 0 # this is supposed to hold the number of ticks we have instanced an object for` on the `Tick` class is not used anywhere.

gollark: Also also, `def __str__(self): pass` doesn't seem to do anything either.

gollark: Also, this function seems to have no valid reason to exist.

This article is issued from Archlinux. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.